{"id":7189,"date":"2026-10-17T15:58:37","date_gmt":"2026-10-17T15:58:37","guid":{"rendered":"https:\/\/utmteknik.com\/industrial-adhesives-and-technical-spray-use-in-manufacturing-and-maintenance\/"},"modified":"2026-10-17T15:58:39","modified_gmt":"2026-10-17T15:58:39","slug":"industrial-adhesives-and-technical-spray-use-in-manufacturing-and-maintenance","status":"publish","type":"page","link":"https:\/\/utmteknik.com\/en\/industrial-adhesives-and-technical-spray-use-in-manufacturing-and-maintenance\/","title":{"rendered":"Industrial Adhesives and Technical Spray Use in Manufacturing and Maintenance"},"content":{"rendered":"\n

Most production downtime starts with a small failure: a loosened bolt, a leaking flange, a worn pump housing or a corroded fastener. Industrial adhesives and technical sprays in manufacturing and maintenance<\/strong> make it possible to fix these problems without replacing parts, without welding or machining, and often without dismantling the machine. The right product shortens maintenance time and extends equipment life.<\/p>\n\n\n\n

On this page you will find the most common applications in industrial plants, from machine repair and assembly lines to corrosion protection and quality control, together with the product groups suited to each task.<\/p>\n\n\n

\n
\"Industrial<\/figure>\n<\/div>\n\n\n

Industrial Adhesives in Machine Maintenance and Repair<\/h2>\n\n\n\n

Repairing Worn and Damaged Parts<\/h3>\n\n\n\n

Pump housings, bearing seats, coupling bores and hydraulic components wear, crack or corrode over time. Metal-filled epoxy resin systems<\/a> are used to rebuild these surfaces and replace lost material. Once cured, they can be machined, drilled and tapped, so equipment can return to service without waiting for a new part. Wear-resistant epoxy systems such as WR2<\/a> suit abrasive surfaces, while steel-filled epoxy resins<\/a> are preferred for parts under impact and load.<\/p>\n\n\n\n

For small leaks and cracks that need immediate attention, epoxy repair products<\/a> such as hand-kneadable repair sticks are a practical solution. Holes in pipes, tanks and castings can be sealed within minutes without tools.<\/p>\n\n\n\n

Threadlocking and Shaft-Hub Joints<\/h3>\n\n\n\n

Vibration is the most common reason bolts work loose in industrial machinery. Anaerobic adhesives<\/a> cure between metal surfaces in the absence of air, locking threaded joints and sealing them at the same time. Low and medium strength grades are used for joints that must be dismantled, and high-strength anaerobic adhesives<\/a> for permanent joints. The same product family is also used to retain bearings, bushings and gear hubs on shafts and to seal flange faces without gaskets.<\/p>\n\n\n\n

Production Line and Assembly Applications<\/h2>\n\n\n\n

In series production, bonding replaces rivets, screws and welding, speeds up assembly, joins dissimilar materials and spreads stress evenly across the joint. Structural acrylic adhesives<\/a> stand out for metal-to-plastic and composite joints, while MS polymer and silicone-based sealants<\/a> are used for panels, cabins and housings that need elastic bonding and sealing. When small parts must be fixed in seconds, cyanoacrylate adhesives<\/a> are the answer.<\/p>\n\n\n\n

Bond quality depends heavily on the surface. Oil, dust and release agent residues significantly reduce bond strength, so surfaces should be cleaned with surface preparation products<\/a> and primed where necessary before application.<\/p>\n\n\n\n

Plant Maintenance with Technical Sprays<\/h2>\n\n\n\n

Cleaning and Degreasing<\/h3>\n\n\n\n

Removing oil, grease and dirt before maintenance is essential for safe work and accurate diagnosis. Cleaners and degreasers<\/a> are available in different formulations for metal surfaces, electrical contacts and other applications. In food and beverage plants, NSF-registered cleaners should be selected.<\/p>\n\n\n\n

Lubrication and Protection of Moving Parts<\/h3>\n\n\n\n

Chains, guides, hinges and pneumatic systems need regular lubrication. Multi-purpose oils<\/a> and grease sprays<\/a> reduce friction and wear while displacing moisture. Where incidental food contact is possible, NSF H1 registered lubricants<\/a> must be used. For joints that become hard to release, assembly sprays<\/a> and anti-seize products allow bolts to be opened easily even after exposure to high temperatures.<\/p>\n\n\n\n

Corrosion Protection<\/h3>\n\n\n\n

Outdoor equipment, steel structures and weld seams must be protected against corrosion. Among our corrosion inhibitors<\/a>, zinc sprays<\/a> are widely used to repair damaged galvanizing and to protect welds.<\/p>\n\n\n\n

Quality Control and Non-Destructive Testing<\/h2>\n\n\n\n

Surface cracks in welded structures, castings and pressure equipment are not always visible to the eye. Crack detection sprays<\/a> reveal surface-breaking cracks using the liquid penetrant method, which consists of cleaner, penetrant and developer steps. For leak testing, leak detection sprays show escaping gas by forming bubbles.<\/p>\n\n\n\n

How to Choose the Right Product<\/h2>\n\n\n\n